Rare traditional fiberglass cutter with a remarkable wooden interior. The hull (#8 of roughly 40) was built by The Sam L. Morse company in Northern California in the 80s with the interior being custom built by a craftsman who spent roughly a decade finishing the interior of this boat with a variety of rare wood species such as Sitka spruce, Alaskan white cedar, and 3/4” thick Burmese teak decks. This boat is a rare work of art. Someone who has a deep admiration for craftsmanship would be the perfect next owner of Jacquelina.
The exterior has had all the old bottom paint removed and is ready for a fresh coat of barrier/bottom paint. The boat has had all old seized thru-hulls removed and will require new bronze seacocks/thru-hulls. The boat does not come with an engine, batteries, head, or range. It has a full sail inventory with battened main, genoa, jib, storm jib & 2 spinnakers. Bowsprit, mast/boom, and rudder (rebuilt in 2008) are all in great shape. Mechanically speaking the boat is a blank slate allowing you to set it up however you wish - outboard vs. inboard, composting head, vs traditional head, induction cooktop vs propane, etc.
The custom-built dual axle trailer comes with the sale and has been completely upgraded with new wheels, tires, and axles. Whether going by land or sea, this boat can go anywhere.
Fatty Knees 7’ sailing dinghy complete with sail, mast, and boom will be included in the sale for full-price offers.
Equipment: New bronze bobstay chainplate 2006 (back-up onboard) Stainless steel sink with whale foot pump (2008) that brings water from 2 20g stainless steel tanks mounted beneath cabin sole to a bronze faucet Two Weems and Plath kerosene lights (2020) All-new LED lights for exterior and interior (2020) Large custom icebox with custom teak shelving and drain to bilge Custom electrical panel (2008) Battery charger (2008) linked to 120V shore power circuit; circuit has 2x120V GFI outlets and circuit breaker Depth finder (2008) with thru-hull transducer Garmin GPS 182C (2005 w/ Chesapeake blue chart) on swing-out arm ICOM VHF with masthead antenna (purchased 2008) Gimbaled compass with lighting (not installed), custom inclinometer Deck mounted custom built Sitka spruce mast and boom with inner mast radar reflector; oversized standing rigging and bronze turnbuckles Three head halyards, one for main, one for genoa and one for chute Fourth halyard goes to block 2/3 way up mast, originally for staysail New custom aluminum 20-gallon fuel tank, never used New cutlass bearing, never used New 1 inch prop shaft with 3 bladed folding max-prop, never used Tons more!
The theoretical maximum speed that a displacement hull can move efficiently through the water is determined by it's waterline length and displacement. It may be unable to reach this speed if the boat is underpowered or heavily loaded, though it may exceed this speed given enough power. Read more.
Classic hull speed formula:
Hull Speed = 1.34 x √LWLA more accurate formula devised by Dave Gerr in The Propeller Handbook replaces the Speed/Length ratio constant of 1.34 with a calculation based on the Displacement/Length ratio.
Max Speed/Length ratio = 8.26 ÷ Displacement/Length ratio.311
Hull Speed = Max Speed/Length ratio x √LWL
A measure of the power of the sails relative to the weight of the boat. The higher the number, the higher the performance, but the harder the boat will be to handle. This ratio is a "non-dimensional" value that facilitates comparisons between boats of different types and sizes. Read more.
SA/D = SA ÷ (D ÷ 64)2/3
A measure of the stability of a boat's hull that suggests how well a monohull will stand up to its sails. The ballast displacement ratio indicates how much of the weight of a boat is placed for maximum stability against capsizing and is an indicator of stiffness and resistance to capsize.
Ballast / Displacement * 100
A measure of the weight of the boat relative to it's length at the waterline. The higher a boat’s D/L ratio, the more easily it will carry a load and the more comfortable its motion will be. The lower a boat's ratio is, the less power it takes to drive the boat to its nominal hull speed or beyond. Read more.
D/L = (D ÷ 2240) ÷ (0.01 x LWL)³
This ratio assess how quickly and abruptly a boat’s hull reacts to waves in a significant seaway, these being the elements of a boat’s motion most likely to cause seasickness. Read more.
Comfort ratio = D ÷ (.65 x (.7 LWL + .3 LOA) x Beam1.33)
This formula attempts to indicate whether a given boat might be too wide and light to readily right itself after being overturned in extreme conditions. Read more.
CSV = Beam ÷ ³√(D / 64)
When talking about the feisty wee Falmouth Cutter, it’s hard to be objective, especially with owners who are universally admiring of their boats. Ferenc Matte in his book The Best Sailboats in the World remarked “the Bristol Channel Cutter and the Falmouth Cutter are the most beautiful 28 and 22 foot fibreglass sailboats in the world”. Well that tells you something.
Both of these designs came from Lyle C. Hess who had something of a love affair for the old British working boats around Falmouth, Cornwall. He took some of their best traits of load carrying ability, speed and seaworthiness while applying a few modernising tweaks to gain a notch in close windedness.
At a dinky 22 feet in length, it stands alongside a select few production pocket cruisers capable of offshore work, immediately we can think of the Dana 24, the Allegra 24 and of course the famous wee Flicka. Like all of these boats, the Falmouth Cutter also has the ability to go to windward at 50 miles an hour up the Interstate on the back of a trailer.
Sailboat writer John Vigor probably sums it up best by describing her as “a very modern old fashioned boat”. She takes the best of today’s construction technology and melds it with the most proven design traits of yesteryear. If you’re in the market for one of these precious packages, the search may be difficult as few come onto the market, and when they do, demand sets a hefty price tag. But you can console yourself with a fabulous resale price should you have the fortitude to part with one.
The Falmouth Cutter follows a lineage back to the 19th century workboats of England. These pilot boats would carry heavy loads in all manner of sea conditions with a good turn of speed, exactly the kind of traits needed today for long distance voyaging. Hess had a lifetime affinity with these boats and for years he visited used book stores and libraries to absorb as much knowledge on them as he could. In all probability it wasn’t only the practicalities of the design that wooed Hess, they are remarkably charming in a husky, old-world kind of way.
His first interpretation of the pilot boat came in 1950 with a 24 foot gaff rigger called the Renegade of Newport which was designed for a friend. The boat caught the interest of one Larry Pardey who had Hess design his marconi rigged version named Seraffyn which was launched in 1968. Fifty thousand copies of the book Cruising in Seraffyn later, Larry and his new wife Lin had made Hess’ designs famous, spurring strong demand for a production boat of that ilk.
The Sam L. Morse Company in California answered the call by introducing Hess’ 28 foot fiberglass Bristol Channel Cutter in 1975. By 1978 the company was working on a smaller version but could still carry two people across ocean stretches in safety. When Hess had completed the design for the Falmouth Cutter, all her numbers indicated that she could be trailered. This added a new unexpected dimension to how the boat could access new cruising grounds.
The boats were built to exacting standards by Sam L. Morse Co. with every aspect of construction screaming quality. In 2007 Cape George Marine, based in Washington were given the rights and the molds to produce the boat. Sam L. Morse stayed in operation through until August 2008, helping Cape George build its first Falmouth Cutter (along with two Bristol Channel Cutters). The last owner of Sam L. Morse Co., Sumio Oya, tells us his company built a total of 39 hulls, the last hull was semi-complete to be finished by its owner.
Since then, Cape George continue to offer the boat at the same price but have yet to produce any additional boats but we are informed they’re considering building a simplified version as a weekender/daysailer with a larger cockpit, cuddy-cabin, and an optional gaff rig.
Despite the traditional pilot boat design’s numerous competencies, Hess managed to improve it with tweaks of his own. Notably he substituted the full length keel with a swept back design that reduced wetted area. He also refined the underbody by introducing more hollow to the garboard area. Both of these changes improved windward ability and speed.
To reduce hobby horsing, the foot of the keel was widened to allow sufficient lead ballast to be concentrated at the center of the keel rather than being distributed along the length, while a wide 8 foot beam gave her better form stability. This was a good thing as Lyle drew a cutter rig that can carry a massive amount of canvas spread out on her lengthy bowsprit and bumpkin. It’s this sail area that helps the wee cutter gain a good turn of speed despite being a boat with only twenty one feet at the waterline.
Going below, the most notable thing is that she’s all wood down there. No plastic hull liners or molded furniture feature in this traditional boat. Owners get access to every part of the hull and being hand built, customers have flexible options. There’s been mention that the factory may be able to build it your way sometimes without costing any extra.
The design was to accomodate two, and indeed there is room for two, but only if you like each other. There’s 5′ 11″ of headroom in the area under the forward hatch and also in the saloon but ducking is required to go between the two. The forward cabin contains a head, a hanging locker, and a double berth to port. Further aft is the galley to port, with a two burner stove and a stainless sink, and on the opposing side an icebox and chart table. There’s two settees in the saloon area and stowage space is surprisingly good.
An inboard engine is standard, but some opt for an outboard which opens up space for a large oversized bed and much more storage.
It’s said the best way to describe the performance of this diminutive cutter is to prepare yourself for a vessel that’s only 21 feet on the waterline, then be pleasantly surprised by the relative turn of speed, with the key word being “relative”.
True to design her seaworthiness in a blow is remarkable and, like most heavy displacement boats, she retains a slow easy motion in trade wind type sailing. She’ll also track well down the face of large swells. In lighter conditions, the bowsprit can be used to fly a cruising spinnaker or a large genoa which gives this tradition boat a surprising performance in light airs.
Finally it’s worth a mentioning that with a draft that measures only 3′ 6″ there’s a certain degree of confidence to be had when exploring coastlines riddled with shallow bays.
Great choice! Your favorites are temporarily saved for this session. Sign in to save them permanently, access them on any device, and receive relevant alerts.