1999 Westsail 32

Atlanta, Georgia, United States
$34,200 USD

Standard features

32 Westsail 1975

W/Central Heat/Air, Roller Furling, 1988 Yanmar Diesel

ELECTRICAL:

Dynarod Bonding Kit Installed Prior to 1999 to Ground the Boats Electrical System, Electronics and Standing Rigging w/Copper Straps That Lead to a Grounding Plate Affixed to Starboard Hull Below Waterline New Perko Battery Selector Switch Installed 6/2002 4/2003, Fuse Panel Replaced w/Blue Sea Systems DC Breaker Panel w/Dual Voltmeters, New 30-amp AC Main Power Distribution Panel Installed and AC Wiring Replaced GFCI Receptacles Installed Throughout Boat Engine Room Completely Rewired 2003 New Stern Light, Combination Deck/Steaming Light, Tricolor Nav Light at Top of Mast and Separate Lower Navigation Lights Mounted on Light Boards on Spreaders) Installed March 2014 plus A TrueCharge2 Series, 20-amp Battery Charger, Remote Panel and Battery Temperature Sensor Installed 4/2015 Number 1 AGM Starting Battery Located in Engine Room Starboard Side Number 2 AGM House Battery Located Beneath Companionway Ladder

ELECTRONICS:

Raytheon Autohelm ST30 Bidata Speed/Depth Instrumentation Platismo Contest 100 Magnetic Compass Autohelm ST2000 Tiller Pilot. Icom IC-M600 HF Marine Transceiver and AT120 HF Automatic Antenna Tuner Icom M59 UHF Transceiver Micrologic Explorer Loran C Receiver Installed by Previous Owner 1988-1992, Prior to his Competing in the 1992 Caribbean 1500.

REFRIDGERATION/HVAC:

April, 2003, Original Icebox was Converted to Rrefrigerator/Freezer w/12vdc Adler/Barbour Super Cold Machine w/Air and Water Cooled Condensing Unit Installed Under Port Settee Central HVAC Added 4/2015 w/ Webasto 110vac 12,000 btu Reverse-Cycle Heat Pump Model FCF12,000. HVAC Components Located in Starboard Engine Compartment and Beneath Nav Table to Starboard.

SAILS:

New Ullman 400 sq. ft. Furling Yankee Cross Cut Sail w/Sunshield and Foam Luff Flattener Installed 10/2003 Like-New 351 Sq. Ft. Mainsail Purchased From Kerns Sails in Costa Mesa, CA (10/2003) and Installed (06/2005) w/New Reefing Lines, Cheek Blocks and Cleats 7 Additional Sails Included w/Owners Purchase of Boat in 1999, Ages Unknown: Spare Hood Mainsail in Fair-Good Condition; Tanbark Staysail, Storm Jib and Storm Trysail in Excellent Condition; Jib and Yankee w/Furling Tape in Good Condition; Drifter w/Wire Luff In Fair Condition

Advertisement

Interested In This Boat?

Have questions? Interested in seeing it?

This listing is presented by SailboatOwners.com. Visit their website for more information or to contact the seller.

View on SailboatOwners.com

Specs

Designers
William Atkin
William Crealock
Colin Archer
Builder
Westsail Corporation
Association
Westsail Owners Association
# Built
830
Hull
Monohull
Keel
Long
Rudder
Transom hung
Construction
FG

Dimensions

Length Overall
39 11 / 12.2 m
Length On Deck
31 11 / 9.8 m
Waterline Length
27 5 / 8.4 m
Beam
10 11 / 3.4 m
Draft
4 11 / 1.5 m
Displacement
19,500 lb / 8,845 kg
Ballast
7,000 lb / 3,175 kg

Rig and Sails

Type
Cutter
Reported Sail Area
663′² / 61.6 m²
Total Sail Area
705′² / 65.5 m²
Mainsail
Sail Area
303′² / 28.1 m²
P
38 3 / 11.7 m
E
15 9 / 4.8 m
Mast Height
49 0 / 14.9 m
Foresail
Sail Area
403′² / 37.4 m²
I
43 11 / 13.4 m
J
18 3 / 5.6 m
Forestay Length
47 7 / 14.5 m

Auxilary Power

Make
Volvo / Perkins
Model
MD2B / MD3B / 4-107
HP
?
Fuel Type
Diesel
Fuel Capacity
70 gal / 265 l
Engine Hours
?

Accomodations

Water Capacity
80 gal / 303 l
Holding Tank Capacity
?
Headroom
6 2 / 1.9 m
Cabins
?

Calculations

Hull Speed
7.03 knots
Sail Area/Displacement
14.64
under powered
Ballast/Displacement
35.9
less stiff, less powerful
Displacement/Length
418.59
ultraheavy
Comfort Ratio
42.54
heavy bluewater boat
Capsize Screening
1.63
better suited for ocean passages

Notes

From BlueWaterBoats.org:

The Westsail 32 goes down in history as the boat that launched a thousand dreams. She’s generally credited for starting the cruising boom of the 1970s which brought “the cruising life” out of the fringes and into the mainstream. Designed by Bill Crealock as a heavy displacement double ender for long distance cruising, this boat is the epitome of seaworthiness; built strong and heavy with huge interior volume. The trade off is in nimbleness; she is slow through the tacks and slow to accelerate. In the early years, often sailed by beginners on badly setup rigs, boat speed was often lacking and she was ridiculed as the “Wet-snail 32” among the bluewater sailing fraternity, however some of this reputation has been shrugged off in recent years. When sailed well the Westsail 32 can surprise.

History

The Westsail 32 started out life as a flush-deck Kendall 32 when Larry Kendall approached Crealock to design a heavy displacement offshore sailboat along the lines of William Aitken’s famous 32 foot double enders Eric and Thistle. It’s said when asked how big the market for such a boat, Crealock estimated 10-12 boats. The Kendall 32 was introduced in 1969 and production exceeded Crealock’s estimates with a run of 30 boats.

It wasn’t until 1971 when a young electrical engineer turned boatbuilder by the name of Snyder Vick who bought the molds did sales begin to take off. He had Crealock redesign the deck layout, adding a cabin house and a revised interior. The new company became Westsail Corporation and the new boat was dubbed the Westsail 32. “Westsail the world” was the advertising mantra, oozing adventure in far away places. So successful was the marketing campaign that by June of 1973 Time Magazine featured a four page spread on “the cruising life” including a large image of a Westsail 32 in a suitably exotic location. It caught the imagination of the American public. The boat sold in incredible numbers, and along the way set in stone the shape and style of American bluewater cruising boats for nearly two decades.

In total 830 boats were produced by Westsail. To keep up with demand around 400 of these boats were sold as hull and deck kits; requiring interior finishing by their respective purchasers. Kits were sold in various stages of completion; Hull and Deck, Sail-Away, and a complete boat. With kits owners could add any option they felt they wanted including ballast, bulkheads, rigging, etc.

Although the Westsail 32 was a runaway marketing success, the company did not enjoy financial success. The petroleum crunch of the 1970’s hit the company hard. Their sales process involved taking orders for boats at fixed prices and selling them out in the order in which they received them. This meant that the company was selling boats up to eighteen months later at prices that were considerably outdated. The company ceased operations in 1981. The molds got sold to P&M Worldwide and another 15 boats were sold in kit form before production finally ceased.

Configuration & Layout

The Westsail 32 follows a long line of traditional double-enders dating back to Colin Archer’s famous 19th century Norwegian pilot boat Regis Voyager which itself was influenced by Archer’s earlier work with designing lifeboats.

A cutter rig sits on top with a bowsprit forward and on some boats a boomkin astern. Below the waterline is a very full keel drawing 5 feet.

The deck arrangement has offshore work in mind. The lifelines are high and the high bulwark combine to provide a sense of security on the foredeck. The cockpit is suitably tiny as was the thinking for blue water sailboats, but it gets crowded quickly with more than two people.

Down below, there’s an enormous interior volume, definitely one of the largest and most livable interiors for 32 feet. There is a huge V-berth forward followed by the head, a port side dinette and starboard settee and a U-shaped galley to port and a starboard navigation station and quarter berth aft. An optional interior featured opposing settees and a centerline table. Later mods included a change in the head configuration and a sit down chart table.

The joinery was aimed more for function than all out beauty and the factory finish varied through the years. Many of the kit boats were finished by their owners superbly, however some are in serious need of TLC.

Construction

The hull is heavily built from hand-laid fiberglass in 12 layers with polyester resin resulting in a hull that ranges from 3/4 inch near the topsides to 1 1/8 inches at the turn of the bilge. The 3/4″ bulkheads are marine plywood and tabbed to the hull with fiberglass.

Ballast varied between boats, but always with at least 7,000 pounds. Some had 2,000 pounds of lead and 5,000 pounds of steel punchings. From 1974, cast lead was used in the keel cavity in three sections. One can easily tell the lead ballast because the keel sump is much deeper under the engine pan.

The deck and cabin trunk is fiberglass cored with two layers of half inch plywood, with an extra two inch plywood base to reinforce below the mast step. Many boats had teak decks at an unbelievably thick (and heavy) 13/16 inches. There were three versions of the deck molds. The first mold had a forward hatch and large heavy sliding companionway with a lazarette hatch that sat up above the deck. The second mold added a center skylight hatch, and the last mold added a cockpit locker, flush lazarette hatch and tapered black anodized aluminum stanchions with aluminum built into the mold for easy on off removal.

Later hulls had fiberglass gudgeons, earlier hulls had stainless steel gudgeons with a bronze pintal.

The hull to deck join with its substantial bulwark is strong, though not impervious to leaking.

Under Sail

The Westsail 32 has a reputation for getting cruisers where they want to go, though not very quickly. According to most owners this is falsely deserved. Motion through the water is comfortable, but the ride has been criticized by some as being relatively wet. Often this is a result of owners overloading their boats. While the boat can easily carry all she needs for comfortable cruising, she will be affected by loading her below her water line. Some owners report the wetness comes from the cockpit seats being flush with the side decks, so any water channeling down the side deck is likely to wet your bottom (some custom boats have this problem solved with a cockpit coaming). Further; later models had a 3″ hawse pipe added midships that eliminated much of water entering the cockpit.

As with many boats with full keels, the boat tracks well but trades this off for maneuverability; both under power and while under canvas. Acceleration is sluggish due to its large wetted area and light weather performance (without the correct sail combination) is nothing to brag about; 10 knots or more is needed before the boats starts moving nicely. The best point of sail is a beam to broad reach between 90 to 120 degrees off the wind with an optimal heal angle of 20 degrees, with good trade winds owners report the boat is capable of  7 knots which is its hull speed.

In the early days the boat had a terrible reputation under sail, perhaps not entirely deserved. Many owners were new to sailing and didn’t have the experience to make a heavy displacement boat perform well. The early rigs weren’t optimal, the mainsails were too big and the headsails too small. The boat gained a reputation for weather helm.

In more recent years the Westsail 32 has turned its slow reputation upside down. In 1988 David King skippered his personally modified** Westsail 32 Saraband to a Trans-Pacific Cup victory, a remarkable feat given the light wind conditions that year. Additionally we hear reports of owners logging week-long consecutive runs of 140 to 160 mile days during trade-wind sailing. Record runs aside, most owners can expect to average around 110 miles per day in the trades.

** David King has documented his modifications for other members of the Westsail Owners Association. The tweaks include subtle modifications to the keel and a revised rig with a smaller mainsail

Buyers Notes

The Westsail 32 has suffered few if any structural problems over the years. It has a solid hull and osmotic blisters that appear on older boats are not an issue with the Westsail.

It’s worth checking out the fuel tanks, especially if they are of black iron. Other areas worth a check are the bottom fittings on the boomkin and the bobstay. Look for signs of rot in the plywood cored decking and signs of fiberglass compression at the mast step. As with any older boat, if the standing rigging is original consider replacing them.

Look for a boat that has 35 hp or more, the original 25hp Volvo MD2B is often reported as insufficient for a distance motoring into adverse weather.

There’s an active owners association at Westsail.org, it’s recommended interested buyers contact them for advice. Additionally, Bud Taplin is an known expert on Westsail boats, he was the first general manager at Westsail, and is now active in providing advice and surveying services for prospective buyers.

As at 2014 the asking price of Westsail 32s are in the range of $30k-$55k USD. Realistically these boats sell 10%-20% below asking price with most trading hands between $30k-$45k USD.

Links, References and Further Reading

» Westsail Owners Association at Westsail.org
» Used Boat Notebook by John Kretschmer, an in depth look at the Westsail 32 (p73-p76)
» Twenty Small Sailboats to Take You Anywhere by John Vigor, (Ch20, p125) an in depth look at the Westsail 32. ISBN:978-0939837328
» Boat US, Jack Horner’s review of the Westsail 32
» Wikipedia’s entry on the Westsail 32
» Westsail the World Documentary trailer on YouTube


Embed

Embed

Embed this page on your own website by copying and pasting this code.

<script src="https://sailboat.guide/embed"
    href="https://sailboat.guide/5c38bj" class="sailboatguide"
    defer></script>

Similar Sailboats For Sale

Great choice! Your favorites are temporarily saved for this session. Sign in to save them permanently, access them on any device, and receive relevant alerts.

We will occasionally send you relevant updates. You can opt out or contact us any time.

Subscribe

Get occassional updates about new features or featured sailboats.
You can opt out or contact us any time.