Great choice! Your favorites are temporarily saved for this session. Sign in to save them permanently, access them on any device, and receive relevant alerts.
Hull / Rig: Full Keel Traditional Fiberglass Masthead Sloop - Tangaroa 32’ LOA, 24’ LWL, 10’ Beam, 4.5’ Draft Designer Ted Hood- 1974 Second Owner New Upholstery (2022) (Edson) Wheel Steering / (Ritchie) Original Binnacle Compass
Sails: Roller Reefing Mainsail 1 Hanked Genoa 1 Roller Furling Headsail (new CDI furler) 1 Storm Jib
Engine / Drive (2020): Yanmar 2GM Diesel, rebuilt, 150Hr. Cutless Bearing & Dripless Packing. 12-gallon Diesel Tank (HDPE)
Water / Waste / Galley: 45 gal. (main) 25 gal. (spare) H20; Holding 12 gallon Manual (Whale) & 12V Bilge Pumps Shower Drain Pump Recent (Whale) Head & Galley Faucet Sets, aux. Manual Galley Faucet Pressure H&C fresh water (Isotherm) 6 gal Water Heater 2-Burner Alcohol Stove (Origo) (Webasto) Icebox to Refrigerator Conversion
Electrical / Electronics: Rebuilt Fuse Panel (Blue Sea) 1 Start 2 House Batteries, 2 Channel Charger / Maintainer Battery Combiner / Disconnect (St’d Horizon) VHF w/ GPS & Remote Handset Depth Finder House & Running Lights all LED
The theoretical maximum speed that a displacement hull can move efficiently through the water is determined by it's waterline length and displacement. It may be unable to reach this speed if the boat is underpowered or heavily loaded, though it may exceed this speed given enough power. Read more.
Classic hull speed formula:
Hull Speed = 1.34 x √LWL
A more accurate formula devised by Dave Gerr in The Propeller Handbook replaces the Speed/Length ratio constant of 1.34 with a calculation based on the Displacement/Length ratio.
Max Speed/Length ratio = 8.26 ÷ Displacement/Length ratio.311
Hull Speed = Max Speed/Length ratio x √LWL
A measure of the power of the sails relative to the weight of the boat. The higher the number, the higher the performance, but the harder the boat will be to handle. This ratio is a "non-dimensional" value that facilitates comparisons between boats of different types and sizes. Read more.
SA/D = SA ÷ (D ÷ 64)2/3
A measure of the stability of a boat's hull that suggests how well a monohull will stand up to its sails. The ballast displacement ratio indicates how much of the weight of a boat is placed for maximum stability against capsizing and is an indicator of stiffness and resistance to capsize.
Ballast / Displacement * 100
A measure of the weight of the boat relative to it's length at the waterline. The higher a boat’s D/L ratio, the more easily it will carry a load and the more comfortable its motion will be. The lower a boat's ratio is, the less power it takes to drive the boat to its nominal hull speed or beyond. Read more.
D/L = (D ÷ 2240) ÷ (0.01 x LWL)³
This ratio assess how quickly and abruptly a boat’s hull reacts to waves in a significant seaway, these being the elements of a boat’s motion most likely to cause seasickness. Read more.
Comfort ratio = D ÷ (.65 x (.7 LWL + .3 LOA) x Beam1.33)
This formula attempts to indicate whether a given boat might be too wide and light to readily right itself after being overturned in extreme conditions. Read more.
CSV = Beam ÷ ³√(D / 64)
Fin keel or keel/cb.
Keel/CB- BU: 3.5’, BD: 7.5’.
Available as sloop, yawl or ketch.
Tall sloop:
I: 40.0’
J: 12.58’
P: 35.1’
E: 13.5’
Yawl rig (mizzen):
PY: 14.18’
EY: 5.78’
This listing is presented by SailboatListings.com. Visit their website for more information or to contact the seller.
Great choice! Your favorites are temporarily saved for this session. Sign in to save them permanently, access them on any device, and receive relevant alerts.
©2025 Sea Time Tech, LLC
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.