CS 36 Merlin is a 35′ 11″ / 11 m monohull sailboat designed by Tony Castro and built by CS Yachts (Canadian Sailcraft) between 1986 and 1990.
- Designer
- Tony Castro
- Builder
- CS Yachts (Canadian Sailcraft)
- Associations
- ?
- # Built
- 100
- Hull
- Monohull
- Keel
- Fin + Bulb
- Rudder
- Spade
- Construction
- FG
Dimensions
- Length Overall
- 35′ 11″ / 11 m
- Waterline Length
- 29′ 2″ / 8.9 m
- Beam
- 11′ 6″ / 3.5 m
- Draft
- 6′ 3″ / 1.9 m
- Displacement
- 13,000 lb / 5,897 kg
- Ballast
- 5,590 lb / 2,536 kg
Rig and Sails
- Type
- Sloop
- Reported Sail Area
- 608′² / 56.5 m²
- Total Sail Area
- 608′² / 56.5 m²
Mainsail
- Sail Area
- 282′² / 26.2 m²
- P
- 39′ 6″ / 12 m
- E
- 14′ 3″ / 4.4 m
- Air Draft
- ?
Foresail
- Sail Area
- 325′² / 30.2 m²
- I
- 45′ 6″ / 13.9 m
- J
- 14′ 3″ / 4.4 m
- Forestay Length
- 47′ 8″ / 14.5 m
Auxilary Power
- Make
- Volvo Penta
- Model
- ?
- HP
- 25
- Fuel Type
- Diesel
- Fuel Capacity
- 40 gal / 151 l
Accomodations
- Water Capacity
- 70 gal / 265 l
- Holding Tank Capacity
- ?
- Headroom
- ?
- Cabins
- ?
Calculations
- Hull Speed
-
8.2 kn
Classic: 7.24 kn
Hull Speed
The theoretical maximum speed that a displacement hull can move efficiently through the water is determined by it's waterline length and displacement. It may be unable to reach this speed if the boat is underpowered or heavily loaded, though it may exceed this speed given enough power. Read more.
Formula
Classic hull speed formula:
Hull Speed = 1.34 x √LWL
A more accurate formula devised by Dave Gerr in The Propeller Handbook replaces the Speed/Length ratio constant of 1.34 with a calculation based on the Displacement/Length ratio.
Max Speed/Length ratio = 8.26 ÷ Displacement/Length ratio.311
Hull Speed = Max Speed/Length ratio x √LWL
- Sail Area/Displacement
-
17.6
Sail Area / Displacement Ratio
A measure of the power of the sails relative to the weight of the boat. The higher the number, the higher the performance, but the harder the boat will be to handle. This ratio is a "non-dimensional" value that facilitates comparisons between boats of different types and sizes. Read more.
Formula
SA/D = SA ÷ (D ÷ 64)2/3
- SA: Sail area in square feet, derived by adding the mainsail area to 100% of the foretriangle area (the lateral area above the deck between the mast and the forestay).
- D: Displacement in pounds.
- Ballast/Displacement
-
43.0
>40: stiffer, more powerful
Ballast / Displacement Ratio
A measure of the stability of a boat's hull that suggests how well a monohull will stand up to its sails. The ballast displacement ratio indicates how much of the weight of a boat is placed for maximum stability against capsizing and is an indicator of stiffness and resistance to capsize.
Formula
Ballast / Displacement * 100
- Displacement/Length
-
233.9
200-300: moderate
Displacement / Length Ratio
A measure of the weight of the boat relative to it's length at the waterline. The higher a boat’s D/L ratio, the more easily it will carry a load and the more comfortable its motion will be. The lower a boat's ratio is, the less power it takes to drive the boat to its nominal hull speed or beyond. Read more.
Formula
D/L = (D ÷ 2240) ÷ (0.01 x LWL)³
- D: Displacement of the boat in pounds.
- LWL: Waterline length in feet
- Comfort Ratio
-
24.7
20-30: coastal cruiser
Comfort Ratio
This ratio assess how quickly and abruptly a boat’s hull reacts to waves in a significant seaway, these being the elements of a boat’s motion most likely to cause seasickness. Read more.
Formula
Comfort ratio = D ÷ (.65 x (.7 LWL + .3 LOA) x Beam1.33)
- D: Displacement of the boat in pounds
- LWL: Waterline length in feet
- LOA: Length overall in feet
- Beam: Width of boat at the widest point in feet
- Capsize Screening
-
2.0
<2.0: better suited for ocean passages
Capsize Screening Formula
This formula attempts to indicate whether a given boat might be too wide and light to readily right itself after being overturned in extreme conditions. Read more.
Formula
CSV = Beam ÷ ³√(D / 64)
- Beam: Width of boat at the widest point in feet
- D: Displacement of the boat in pounds
Notes
The CS 36 MERLIN, while having similar dimensions to the CS 36 TRADITIONAL, is a completely different design. While it was being produced a purchaser had five pages of options to choose from— a Kevlar or fibreglass hull; a swim platform or regular transom; a 28 hp diesel or a 43 hp turbo; a tall or regular rig and by the end, four keel configurations (shoal, wing, deep and performance bulb). As a result, other than the 20 or so that went into charter, no two Merlins are alike.
Contruction standards were high. The hull was hand-laid fibreglass or Kevlar with balsa core above the water and both hull and deck were vacuum bagged.
Wing keel version draft: 5.00’ / 1.52m
