Great choice! Your favorites are temporarily saved for this session. Sign in to save them permanently, access them on any device, and receive relevant alerts.
Go to Sailing Texas classifieds for current sailboats for sale Macgregor 26X, 2001 sailboat for sale Albuquerque, NM Price $9500
Length 25’ 10” Draft 9” Water balast Fiberglass swing keel extends 5’6” deep Self-righting and unsinkable (integral flotation) 8’-4” Beam – legal travel width Trailer with side rails 50 HP Nissan fuel (2- 6 gal tanks) Two new House/Starting batteries Battery “1-2-Both” master switch Furling Jib with Sunbrella protection Main – new- Condition Sail Covers Anchor Mast Raising System with gen pole Dock lines and fenders Bimini Cockpit Cushions Swim Ladder Cabin Lights Kitchen and Bath Sinks with hand pumped Table with bench seating Enclosed Head with porta-potty V-berth sleeps 2 Full size beneath cockpit – sleeps 2 tall people Beneath seat cooler and storage Life Jackets
SOLD
The theoretical maximum speed that a displacement hull can move efficiently through the water is determined by it's waterline length and displacement. It may be unable to reach this speed if the boat is underpowered or heavily loaded, though it may exceed this speed given enough power. Read more.
Classic hull speed formula:
Hull Speed = 1.34 x √LWL
A more accurate formula devised by Dave Gerr in The Propeller Handbook replaces the Speed/Length ratio constant of 1.34 with a calculation based on the Displacement/Length ratio.
Max Speed/Length ratio = 8.26 ÷ Displacement/Length ratio.311
Hull Speed = Max Speed/Length ratio x √LWL
A measure of the power of the sails relative to the weight of the boat. The higher the number, the higher the performance, but the harder the boat will be to handle. This ratio is a "non-dimensional" value that facilitates comparisons between boats of different types and sizes. Read more.
SA/D = SA ÷ (D ÷ 64)2/3
A measure of the stability of a boat's hull that suggests how well a monohull will stand up to its sails. The ballast displacement ratio indicates how much of the weight of a boat is placed for maximum stability against capsizing and is an indicator of stiffness and resistance to capsize.
Ballast / Displacement * 100
A measure of the weight of the boat relative to it's length at the waterline. The higher a boat’s D/L ratio, the more easily it will carry a load and the more comfortable its motion will be. The lower a boat's ratio is, the less power it takes to drive the boat to its nominal hull speed or beyond. Read more.
D/L = (D ÷ 2240) ÷ (0.01 x LWL)³
This ratio assess how quickly and abruptly a boat’s hull reacts to waves in a significant seaway, these being the elements of a boat’s motion most likely to cause seasickness. Read more.
Comfort ratio = D ÷ (.65 x (.7 LWL + .3 LOA) x Beam1.33)
This formula attempts to indicate whether a given boat might be too wide and light to readily right itself after being overturned in extreme conditions. Read more.
CSV = Beam ÷ ³√(D / 64)
As sail/power ‘hybrids’, both the M and X models are designed for use with a more than ‘auxilary’ sized outboard and water ballast.
The MACGREGOR 26M replaced the MACGREGOR 26X in 2003.
A similar version later reintroduced from another builder as the TATTOO 26 (2013).
This listing is presented by SailingTexas.com. Visit their website for more information or to contact the seller.
Great choice! Your favorites are temporarily saved for this session. Sign in to save them permanently, access them on any device, and receive relevant alerts.
©2024 Sea Time Tech, LLC
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.