Great choice! Your favorites are temporarily saved for this session. Sign in to save them permanently, access them on any device, and receive relevant alerts.

We will occasionally send you relevant updates. You can opt out or contact us any time.
  • 1 / 5
  • 2 / 5
  • 3 / 5
  • 4 / 5
  • 5 / 5

1987 Passport Yachts Passport 40

$35,000 USD

Seller's Description

1987 Passport 40 in fair condition with unfinished electric engine project. May 2023 survey available including some current pics. Listing picture from 2015. Radar Arch added 2018. Been on the hard since July 2022. Comprehensive work logs by owner until Sep. 2022.

Equipment: Mainsail: 2012 Flex Poly Cruise RF Genoa: 2019 Vectran Cruise Laminate RF Staysail: 2019 Vectran Cruise Laminate Whisker Pole solar panels wind generator Dyneema rigging Boom gallows Spade anchor S120 (55lb)-galvanized steel



Robert Perry
Passport Yachts
# Built
Also Known As


Length Overall
39 8 / 12.1 m
Waterline Length
33 5 / 10.2 m
12 8 / 3.9 m
5 9 / 1.8 m
22,770 lb / 10,329 kg
8,600 lb / 3,901 kg

Rig and Sails

Reported Sail Area
762′² / 70.8 m²
Total Sail Area
762′² / 70.8 m²
Sail Area
367′² / 34.1 m²
45 10 / 14 m
16 0 / 4.9 m
Air Draft
Sail Area
395′² / 36.7 m²
50 7 / 15.4 m
15 7 / 4.8 m
Forestay Length
52 11 / 16.1 m

Auxilary Power

Fuel Type
Fuel Capacity
128 gal / 484 l
Engine Hours


Water Capacity
135 gal / 511 l
Holding Tank Capacity


Hull Speed
8.4 kn
Classic: 7.75 kn

Hull Speed

The theoretical maximum speed that a displacement hull can move efficiently through the water is determined by it's waterline length and displacement. It may be unable to reach this speed if the boat is underpowered or heavily loaded, though it may exceed this speed given enough power. Read more.


Classic hull speed formula:

Hull Speed = 1.34 x √LWL

A more accurate formula devised by Dave Gerr in The Propeller Handbook replaces the Speed/Length ratio constant of 1.34 with a calculation based on the Displacement/Length ratio.

Max Speed/Length ratio = 8.26 ÷ Displacement/Length ratio.311
Hull Speed = Max Speed/Length ratio x √LWL

8.35 knots
Classic formula: 7.75 knots
Sail Area/Displacement
<16: under powered

Sail Area / Displacement Ratio

A measure of the power of the sails relative to the weight of the boat. The higher the number, the higher the performance, but the harder the boat will be to handle. This ratio is a "non-dimensional" value that facilitates comparisons between boats of different types and sizes. Read more.


SA/D = SA ÷ (D ÷ 64)2/3

  • SA: Sail area in square feet, derived by adding the mainsail area to 100% of the foretriangle area (the lateral area above the deck between the mast and the forestay).
  • D: Displacement in pounds.
<16: under powered
16-20: good performance
>20: high performance
<40: less stiff, less powerful

Ballast / Displacement Ratio

A measure of the stability of a boat's hull that suggests how well a monohull will stand up to its sails. The ballast displacement ratio indicates how much of the weight of a boat is placed for maximum stability against capsizing and is an indicator of stiffness and resistance to capsize.


Ballast / Displacement * 100

<40: less stiff, less powerful
>40: stiffer, more powerful
200-275: moderate

Displacement / Length Ratio

A measure of the weight of the boat relative to it's length at the waterline. The higher a boat’s D/L ratio, the more easily it will carry a load and the more comfortable its motion will be. The lower a boat's ratio is, the less power it takes to drive the boat to its nominal hull speed or beyond. Read more.


D/L = (D ÷ 2240) ÷ (0.01 x LWL)³

  • D: Displacement of the boat in pounds.
  • LWL: Waterline length in feet
<100: ultralight
100-200: light
200-300: moderate
300-400: heavy
>400: very heavy
Comfort Ratio
30-40: moderate bluewater cruising boat

Comfort Ratio

This ratio assess how quickly and abruptly a boat’s hull reacts to waves in a significant seaway, these being the elements of a boat’s motion most likely to cause seasickness. Read more.


Comfort ratio = D ÷ (.65 x (.7 LWL + .3 LOA) x Beam1.33)

  • D: Displacement of the boat in pounds
  • LWL: Waterline length in feet
  • LOA: Length overall in feet
  • Beam: Width of boat at the widest point in feet
<20: lightweight racing boat
20-30: coastal cruiser
30-40: moderate bluewater cruising boat
40-50: heavy bluewater boat
>50: extremely heavy bluewater boat
Capsize Screening
<2.0: better suited for ocean passages

Capsize Screening Formula

This formula attempts to indicate whether a given boat might be too wide and light to readily right itself after being overturned in extreme conditions. Read more.


CSV = Beam ÷ ³√(D / 64)

  • Beam: Width of boat at the widest point in feet
  • D: Displacement of the boat in pounds
<2: better suited for ocean passages
>2: better suited for coastal cruising



The Passport 40 comes from the first generation of performance cruisers for which its designer, Robert Perry, has generally been credited with when he introduced his groundbreaking Valiant 40. The Passport 40 has a similar underbody to the Valiant but most strikingly different a first glance is the use of a transom over Perry’s usual double-ended stern.

Introduced in 1980, the Passport 40 has become one of Perrys more successful 40-footers. With their sensible interiors, quality Taiwanese build and sailing characteristics described as nimble, fast and sea-kindly, it’s no wonder.


The Passport 40 project was kicked off in 1978 when Wendell Renken of Passport Yachts wrote from Taiwan to Perry commissioning a design for a 40-footer. The request as Perry recalls was for an interior based on his previous work on the Freeport 36 with Islander Yachts. It’s interesting to note that Perry accepted the commission by asking for a hefty upfront fee instead of the usual designer’s fee and commission arrangement after noting the dubious nature of the letter’s stationary, “Yacht Builders, Frozen Foods, and Eel Farms.”

The fee proved no impediment and the boat was duly penned and then built by King Dragon boatyard in Taiwan. It was after all the boom years for Taiwanese boatbuilding with exchange rates and cheap but good quality craftmanship favoring the exchange. The Passport 40 was introduced in 1980 and production continued for just over a decade through to 1991 with a final tally of 148 boats built before the design was tweaked into the Passport 41 with an extra foot incorporating a reverse transom and swim platform. The design was eventually massaged into the Passport 43 which had the stern extended even further and five extra feet added to the rig which was revised to two spreaders. Including the Passport 41 and Passport 43 at total of 163 boats were built.


Perry has penned some fantastic boats in his career, the Passport 40 shares company with the Valiant 40 and the Baba 40 as being his most popular in the 40-foot range so it’s interesting to note all three share the basic hull lines which the Valiant 40 pioneered. Where Perry makes a departure from his usual formula of that era is the choice of a standard transom instead of his normal canoe stern.

The sheerline line is sweeping and handsome. Below the waterline a cruising fin keel drawing 5′ 9″ and a skeg hung rudder, their profiles looking very similar to the Valiant 40. There is a shoal draft option that draws a useful 5′ 3″.

Passport 40s came with a sloop rig as standard equipment, though almost all boats have been fitted with a inner stay, usually the removable type producing a double headsail cutter style rig more suited for crossing oceans. John Kretschmer mentions in Sailing Magazine that the original design objective was to allow the boat to be sailed under a single mainsail alone.


Above deck the Passport 40 has a sensibly designed cockpit for seagoing action, there’s room for up to four with wide seats and a coaming that’s trimmed in teak, large cockpit drains, and plenty of cockpit locker space. All the sail control lines are fed back into the cockpit and the main winches within easy reach of the helm to ease single handing.

The side decks are relatively wide with a molded in bulwark that provides for a secure feel when moving to the fore-deck. You’ll notice a fair amount of teak; from the caprail to handrails to the eyebrows on the coachroof. Deck fittings tend to be solid and of top quality, the original boat had a single bow roller as standard, but many have opted for double rollers and have since updated with a electric windlass.

Down below the interior feel is really nice. The joinery, finished in teak, is superb, though the sheer quantity of teak can be a bit dark for some. It’s said most Passport 40 interiors were semi-custom in nature so expect some variation here, roughly half of the boats were configured with a pullman berth placed forward with a head at the forepeak and the other half with a traditional v-berth layout. The pullman berth arrangement tends to be more practical as the berth situated a little back is more comfortable and the head at the forepeak doesn’t mind if it gets seaspray from an open forward hatch. All boats feature a seagoing quarter berth sleeping two in the starboard aft cabin.

The U-shaped galley to port is large and dominates the main saloon area. It’s functional with plenty of pantry space, large refrigeration bins, and features twin sinks not too far from the boat’s centerline. The nav station to starboard varies between boats and can be found facing in forwards, aft, or outwards.

Further forward, the living space includes a large L-shaped settee (U shaped on some) surrounding a large teak table to port and a single settee opposite, again, there is plenty of storage behind the settees.

The engine is located under the saloon table and provides good access. Owners have reported the engine removal and replacement is particularly easy on the Passport 40.


Like most GRP boats built in Taiwan of that era, the Passport 40’s hull was built strong and heavy with lots of polyester resin and glass. Renkin in particular had the hull built thicker than Perry’s design spec, arguing the solidity was what buyers loved.

The ballast was of iron encapsulated in GRP. Decks were originally cored in marine ply with resin barriers to limit potential for rot damage from leaks. Later boats moved to Airex foam coring. The hull-to-deck joint is bonded and through-bolted on an inward flange on the raised bulwark, there’s also a steel strip embedded into the bulwark for mounting the stanchions. Over time this strip has been made refitting more difficult. On most boats the mast is keel stepped. Bulkheads and internal furniture are fiberglassed into the hull.

Under Sail

The Passport 40 has all the sailing characteristics of a good passage-maker. They are beautifully balanced, fast, yet preserve crew energies by being seakindly with a soft easy motion. They perform quite well in light winds and really come to life when the weather picks up, especially on the beam. Downwind they track well enough for the speed lovers to fly spinnakers under self steering with no problems. You can expect routine 130-140 miles days in the trades, but with fair winds and 24/7 hand steering we hear of numbers as high as 190, even 200 miles per day have been clocked.

Buyers Notes

The Passport 40 has held its value well since its introduction, testament to its original build quality and owner appeal. Many boats on the market have been well looked after. That said, there are some standard things to inspect for on the Passport 40:

  • With most teak decks of significant age, the screws holding them down are often a source of leaks and deck rot.
  • Standing rigging should be inspected and replaced as necessary.
  • The original stainless steel chainplates were of lower quality and subject to leaks, inspected for leaks and signs of corrosion.
  • The fuel tanks are of black iron, which on other boats have been a weak point, in the case of the Passport 40 they have been glassed over externally to help mitigate corrosion from the outside. They are worth an inspection in any regards. Later models switched to aluminum tanks.
  • It’s been reported that mild steel was used in the rudder cage as well as the mast step and both have been sources of corrosion, inspect closely.
  • Look closely at the joinery for signs of creep and movement, it’s been an issue on a few boats. The consensus is that this is probably caused on boats that have had their rigging tensioned really tight in the past.

For further research it’s worth contacting other owners on the Passport 40 email list run on Google Groups.

As of 2010, the asking price of Passport 40s are in the range of $110k-$190k USD.

Links, References and Further Reading

» Passport 40 owners email list on Google Groups
» Sailing Magazine’s review of the Passport 40 by John Kretschmer
» Yacht Design According to Perry: My Boats and What Shaped Them, by Robert H. Perry (Ch 9)
» Sailing Magazine’s review of the Passport 40 by John Kretschmer
» Passport 40, Evolution of the Valiant 40 by Jordan Yachts

This listing is presented by Visit their website for more information or to contact the seller.

View on




Embed this page on your own website by copying and pasting this code.

Similar Sailboats For Sale

Great choice! Your favorites are temporarily saved for this session. Sign in to save them permanently, access them on any device, and receive relevant alerts.

We will occasionally send you relevant updates. You can opt out or contact us any time.

©2024 Sea Time Tech, LLC

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.