Jollyboat

1950
Designer
Uffa Fox
Builders
Fairey Marine Ltd
O'Day Corp.
Columbia Yachts
Association
Classic & Vintage Racing Dinghy Association
# Built
500
Hull
Monohull Dinghy
Keel
Centerboard
Rudder
?
Construction
Wood or FG

Dimensions

Length Overall
18 0 / 5.5 m
Waterline Length
17 5 / 5.3 m
Beam
4 11 / 1.5 m
Draft
0 7 / 0.2 m 4 9 / 1.5 m
Displacement
300 lb / 136 kg
Ballast
?
• 1 / 1

Rig and Sails

Type
Sloop
Reported Sail Area
160′² / 14.9 m²
Total Sail Area
?
Sail Area
?
P
?
E
?
Air Draft
?
Sail Area
?
I
?
J
?
Forestay Length
?

Make
?
Model
?
HP
?
Fuel Type
?
Fuel Capacity
?

Accomodations

Water Capacity
?
Holding Tank Capacity
?
?
Cabins
?

Hull Speed
12.7 kn
Classic: 5.6 kn

Hull Speed

The theoretical maximum speed that a displacement hull can move efficiently through the water is determined by it's waterline length and displacement. It may be unable to reach this speed if the boat is underpowered or heavily loaded, though it may exceed this speed given enough power. Read more.

Formula

Classic hull speed formula:

Hull Speed = 1.34 x √LWL

A more accurate formula devised by Dave Gerr in The Propeller Handbook replaces the Speed/Length ratio constant of 1.34 with a calculation based on the Displacement/Length ratio.

Max Speed/Length ratio = 8.26 ÷ Displacement/Length ratio.311
Hull Speed = Max Speed/Length ratio x √LWL

12.69 knots
Classic formula: 5.6 knots
Sail Area/Displacement
57.1
>20: high performance

Sail Area / Displacement Ratio

A measure of the power of the sails relative to the weight of the boat. The higher the number, the higher the performance, but the harder the boat will be to handle. This ratio is a "non-dimensional" value that facilitates comparisons between boats of different types and sizes. Read more.

Formula

SA/D = SA ÷ (D ÷ 64)2/3

• SA: Sail area in square feet, derived by adding the mainsail area to 100% of the foretriangle area (the lateral area above the deck between the mast and the forestay).
• D: Displacement in pounds.
57.13
<16: under powered
16-20: good performance
>20: high performance
Ballast/Displacement
?

Ballast / Displacement Ratio

A measure of the stability of a boat's hull that suggests how well a monohull will stand up to its sails. The ballast displacement ratio indicates how much of the weight of a boat is placed for maximum stability against capsizing and is an indicator of stiffness and resistance to capsize.

Formula

Ballast / Displacement * 100

?
<40: less stiff, less powerful
>40: stiffer, more powerful
Displacement/Length
25.0
<100: Ultralight

Displacement / Length Ratio

A measure of the weight of the boat relative to it's length at the waterline. The higher a boat’s D/L ratio, the more easily it will carry a load and the more comfortable its motion will be. The lower a boat's ratio is, the less power it takes to drive the boat to its nominal hull speed or beyond. Read more.

Formula

D/L = (D ÷ 2240) ÷ (0.01 x LWL)³

• D: Displacement of the boat in pounds.
• LWL: Waterline length in feet
25.03
<100: ultralight
100-200: light
200-300: moderate
300-400: heavy
>400: very heavy
Comfort Ratio
3.1
<20: lightweight racing boat

Comfort Ratio

This ratio assess how quickly and abruptly a boat’s hull reacts to waves in a significant seaway, these being the elements of a boat’s motion most likely to cause seasickness. Read more.

Formula

Comfort ratio = D ÷ (.65 x (.7 LWL + .3 LOA) x Beam1.33)

• D: Displacement of the boat in pounds
• LWL: Waterline length in feet
• LOA: Length overall in feet
• Beam: Width of boat at the widest point in feet
3.07
<20: lightweight racing boat
20-30: coastal cruiser
30-40: moderate bluewater cruising boat
40-50: heavy bluewater boat
>50: extremely heavy bluewater boat
Capsize Screening
3.0
>2.0: better suited for coastal cruising

Capsize Screening Formula

This formula attempts to indicate whether a given boat might be too wide and light to readily right itself after being overturned in extreme conditions. Read more.

Formula

CSV = Beam ÷ ³√(D / 64)

• Beam: Width of boat at the widest point in feet
• D: Displacement of the boat in pounds
2.98
<2: better suited for ocean passages
>2: better suited for coastal cruising

Notes

The first boats were ‘hot molded’ with wood veneers, using a method developed by Fairey Marine’s parent company for aircraft construction during WWII. (Fairey Marine built around 370 boats.)
In addition to it’s initial popularity in the UK, a number were imported to the US by George O’Day, an agent for Fairey Marine at the time. Boats were also built and raced in Australia and New Zealand.
Trapezes were legalized in 1959. A few were built of fiberglass by (among others)Columbia Yachts (USA) in the mid 1960’s but, reportedly, the technology had not progressed far enough at this time to match the rigidity and light weight of the wood boats. JOLLYBOAT class racing had mostly vanished by 1970.

For Sale

Have a sailboat to sell?