Paceship 32 (Tripp)

1968 — 1975
Designer
William H. Tripp Jr.
Builder
Paceship Yachts Ltd.
Association
Paceship/AMF Yachts Website
# Built
?
Hull
Monohull
Keel
Fin
Rudder
Skeg
Construction
FG

Dimensions

Length Overall
31 9 / 9.7 m
Waterline Length
22 11 / 7 m
Beam
10 2 / 3.1 m
Draft
4 11 / 1.5 m
Displacement
10,600 lb / 4,808 kg
Ballast
2,600 lb / 1,179 kg (Iron)

Rig and Sails

Type
Sloop
Reported Sail Area
477′² / 44.3 m²
Total Sail Area
495′² / 46 m²
Sail Area
259′² / 24 m²
P
34 6 / 10.5 m
E
14 11 / 4.6 m
Air Draft
?
Sail Area
236′² / 21.9 m²
I
39 3 / 12 m
J
12 0 / 3.7 m
Forestay Length
41 0 / 12.5 m

Make
?
Model
?
HP
?
Fuel Type
?
Fuel Capacity
?

Accomodations

Water Capacity
?
Holding Tank Capacity
?
?
Cabins
?

Hull Speed
6.2 kn
Classic: 6.43 kn

Hull Speed

The theoretical maximum speed that a displacement hull can move efficiently through the water is determined by it's waterline length and displacement. It may be unable to reach this speed if the boat is underpowered or heavily loaded, though it may exceed this speed given enough power. Read more.

Formula

Classic hull speed formula:

Hull Speed = 1.34 x √LWL

A more accurate formula devised by Dave Gerr in The Propeller Handbook replaces the Speed/Length ratio constant of 1.34 with a calculation based on the Displacement/Length ratio.

Max Speed/Length ratio = 8.26 ÷ Displacement/Length ratio.311
Hull Speed = Max Speed/Length ratio x √LWL

6.2 knots
Classic formula: 6.43 knots
Sail Area/Displacement
15.8
<16: under powered

Sail Area / Displacement Ratio

A measure of the power of the sails relative to the weight of the boat. The higher the number, the higher the performance, but the harder the boat will be to handle. This ratio is a "non-dimensional" value that facilitates comparisons between boats of different types and sizes. Read more.

Formula

SA/D = SA ÷ (D ÷ 64)2/3

• SA: Sail area in square feet, derived by adding the mainsail area to 100% of the foretriangle area (the lateral area above the deck between the mast and the forestay).
• D: Displacement in pounds.
15.82
<16: under powered
16-20: good performance
>20: high performance
Ballast/Displacement
24.5
<40: less stiff, less powerful

Ballast / Displacement Ratio

A measure of the stability of a boat's hull that suggests how well a monohull will stand up to its sails. The ballast displacement ratio indicates how much of the weight of a boat is placed for maximum stability against capsizing and is an indicator of stiffness and resistance to capsize.

Formula

Ballast / Displacement * 100

24.52
<40: less stiff, less powerful
>40: stiffer, more powerful
Displacement/Length
389.0
>350: ultraheavy

Displacement / Length Ratio

A measure of the weight of the boat relative to it's length at the waterline. The higher a boat’s D/L ratio, the more easily it will carry a load and the more comfortable its motion will be. The lower a boat's ratio is, the less power it takes to drive the boat to its nominal hull speed or beyond. Read more.

Formula

D/L = (D ÷ 2240) ÷ (0.01 x LWL)³

• D: Displacement of the boat in pounds.
• LWL: Waterline length in feet
388.99
<100: ultralight
100-200: light
200-300: moderate
300-400: heavy
>400: very heavy
Comfort Ratio
28.9
20-30: coastal cruiser

Comfort Ratio

This ratio assess how quickly and abruptly a boat’s hull reacts to waves in a significant seaway, these being the elements of a boat’s motion most likely to cause seasickness. Read more.

Formula

Comfort ratio = D ÷ (.65 x (.7 LWL + .3 LOA) x Beam1.33)

• D: Displacement of the boat in pounds
• LWL: Waterline length in feet
• LOA: Length overall in feet
• Beam: Width of boat at the widest point in feet
28.88
<20: lightweight racing boat
20-30: coastal cruiser
30-40: moderate bluewater cruising boat
40-50: heavy bluewater boat
>50: extremely heavy bluewater boat
Capsize Screening
1.9
<2.0: better suited for ocean passages

Capsize Screening Formula

This formula attempts to indicate whether a given boat might be too wide and light to readily right itself after being overturned in extreme conditions. Read more.

Formula

CSV = Beam ÷ ³√(D / 64)

• Beam: Width of boat at the widest point in feet
• D: Displacement of the boat in pounds
1.85
<2: better suited for ocean passages
>2: better suited for coastal cruising

Notes

It is thought that the first of these hulls were made by Beetle Boats of RI. By 1958 it became the GALAXY 32 made by the American Boatbuilding Corp. During the ‘60s they produced nine boats along with Beetle Boats who were reputed to have made several more. A few boats are known to have been built by Coleman Boat Co. The original molds were sold to Metalmast Marine where 5 more were completed in the early 70’s.
Paceship Yachts of Canada turned out their own version, the PACESHIP 32 (Ad shown in 1966).
(By 1973, Paceship was calling this yacht the TRIPP 32.)
Dimensions shown are from a Paceship magazine ad in 1966.
(rig dimensions contributed by a user and not from a sail plan.)

For Sale

Have a sailboat to sell?