# Frisco Flyer III

1964
Designer
Tord Sundén
Builder
Cheoy Lee Shipyard
Associations
?
# Built
?
Hull
Monohull
Keel
Long
Rudder
Transom hung
Construction
FG

### Dimensions

Length Overall
25 0 / 7.6 m
Waterline Length
19 5 / 5.9 m
Beam
7 3 / 2.2 m
Draft
3 10 / 1.2 m
Displacement
5,500 lb / 2,495 kg
Ballast
2,500 lb / 1,134 kg
• 1 / 1

### Rig and Sails

Type
Sloop
Reported Sail Area
304′² / 28.2 m²
Total Sail Area
?
Sail Area
?
P
?
E
?
Air Draft
?
Sail Area
?
I
?
J
?
Forestay Length
?

Make
?
Model
?
HP
?
Fuel Type
?
Fuel Capacity
?

### Accomodations

Water Capacity
?
Holding Tank Capacity
?
Headroom
?
Cabins
?

Hull Speed
6.0 kn
Classic: 5.92 kn

### Hull Speed

The theoretical maximum speed that a displacement hull can move efficiently through the water is determined by it's waterline length and displacement. It may be unable to reach this speed if the boat is underpowered or heavily loaded, though it may exceed this speed given enough power. Read more.

Formula

Classic hull speed formula:

Hull Speed = 1.34 x √LWL

A more accurate formula devised by Dave Gerr in The Propeller Handbook replaces the Speed/Length ratio constant of 1.34 with a calculation based on the Displacement/Length ratio.

Max Speed/Length ratio = 8.26 ÷ Displacement/Length ratio.311
Hull Speed = Max Speed/Length ratio x √LWL

6.0 knots
Classic formula: 5.92 knots
Sail Area/Displacement
15.6
<16: under powered

### Sail Area / Displacement Ratio

A measure of the power of the sails relative to the weight of the boat. The higher the number, the higher the performance, but the harder the boat will be to handle. This ratio is a "non-dimensional" value that facilitates comparisons between boats of different types and sizes. Read more.

Formula

SA/D = SA ÷ (D ÷ 64)2/3

• SA: Sail area in square feet, derived by adding the mainsail area to 100% of the foretriangle area (the lateral area above the deck between the mast and the forestay).
• D: Displacement in pounds.
15.61
<16: under powered
16-20: good performance
>20: high performance
Ballast/Displacement
45.5
>40: stiffer, more powerful

### Ballast / Displacement Ratio

A measure of the stability of a boat's hull that suggests how well a monohull will stand up to its sails. The ballast displacement ratio indicates how much of the weight of a boat is placed for maximum stability against capsizing and is an indicator of stiffness and resistance to capsize.

Formula

Ballast / Displacement * 100

45.45
<40: less stiff, less powerful
>40: stiffer, more powerful
Displacement/Length
331.8
275-350: heavy

### Displacement / Length Ratio

A measure of the weight of the boat relative to it's length at the waterline. The higher a boat’s D/L ratio, the more easily it will carry a load and the more comfortable its motion will be. The lower a boat's ratio is, the less power it takes to drive the boat to its nominal hull speed or beyond. Read more.

Formula

D/L = (D ÷ 2240) ÷ (0.01 x LWL)³

• D: Displacement of the boat in pounds.
• LWL: Waterline length in feet
331.77
<100: ultralight
100-200: light
200-300: moderate
300-400: heavy
>400: very heavy
Comfort Ratio
28.5
20-30: coastal cruiser

### Comfort Ratio

This ratio assess how quickly and abruptly a boat’s hull reacts to waves in a significant seaway, these being the elements of a boat’s motion most likely to cause seasickness. Read more.

Formula

Comfort ratio = D ÷ (.65 x (.7 LWL + .3 LOA) x Beam1.33)

• D: Displacement of the boat in pounds
• LWL: Waterline length in feet
• LOA: Length overall in feet
• Beam: Width of boat at the widest point in feet
28.51
<20: lightweight racing boat
20-30: coastal cruiser
30-40: moderate bluewater cruising boat
40-50: heavy bluewater boat
>50: extremely heavy bluewater boat
Capsize Screening
1.6
<2.0: better suited for ocean passages

### Capsize Screening Formula

This formula attempts to indicate whether a given boat might be too wide and light to readily right itself after being overturned in extreme conditions. Read more.

Formula

CSV = Beam ÷ ³√(D / 64)

• Beam: Width of boat at the widest point in feet
• D: Displacement of the boat in pounds
1.64
<2: better suited for ocean passages
>2: better suited for coastal cruising

### Notes

The FRISCO FLYER was first produced as the PACIFIC CLIPPER and later as the OFFSHORE 26. The name “Frisco Flyer” originated with the Richard Reed, yacht brokerage in San Francisco. Their brochure decribed it as a “modified Folkboat.” The FOLKBOAT was originally designed by Tord Sunden, and modifications to the design were made by unnamed Cheoy Lee staff. There are three types, all available with various options (diesel vs. gas, stainless vs. plow steel rigging, canvas vs. teak decks, etc.):
a. PACIFIC CLIPPER: all teak, small trunk cabin, original Folkboat-like fractional rig with double spreaders and returning shrouds. Sometimes referred to as a FRISCO FLYER Mark I.
b. FRISCO FLYER Mark II, larger teak trunk cabin, masthead rig.
c. FRISCO FLYER Mark III, larger teak doghouse cabin, some standing headroom, masthead rig.
The first one built was built in 1957 and made two single-handed Atlantic crossings that year, after which the company went into production on the model.

### For Sale

Have a sailboat to sell?
List it for free and it will show up here.
Advertisement

Great choice! Your favorites are temporarily saved for this session. Sign in to save them permanently, access them on any device, and receive relevant alerts.

We will occasionally send you relevant updates. You can opt out or contact us any time.

### Subscribe

Get occassional updates about new features or featured sailboats.
You can opt out or contact us any time.
Measurements:

Made with ♥ by the founders of Refit Guide
©2022 Sea Time Tech, LLC

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.