The theoretical maximum speed that a displacement hull can move efficiently through the water is determined by it's waterline length and displacement. It may be unable to reach this speed if the boat is underpowered or heavily loaded, though it may exceed this speed given enough power. Read more.
Classic hull speed formula:
Hull Speed = 1.34 x √LWLA more accurate formula devised by Dave Gerr in The Propeller Handbook replaces the Speed/Length ratio constant of 1.34 with a calculation based on the Displacement/Length ratio.
Max Speed/Length ratio = 8.26 ÷ Displacement/Length ratio.311
Hull Speed = Max Speed/Length ratio x √LWL
A measure of the power of the sails relative to the weight of the boat. The higher the number, the higher the performance, but the harder the boat will be to handle. This ratio is a "non-dimensional" value that facilitates comparisons between boats of different types and sizes. Read more.
SA/D = SA ÷ (D ÷ 64)2/3
A measure of the stability of a boat's hull that suggests how well a monohull will stand up to its sails. The ballast displacement ratio indicates how much of the weight of a boat is placed for maximum stability against capsizing and is an indicator of stiffness and resistance to capsize.
Ballast / Displacement * 100
A measure of the weight of the boat relative to it's length at the waterline. The higher a boat’s D/L ratio, the more easily it will carry a load and the more comfortable its motion will be. The lower a boat's ratio is, the less power it takes to drive the boat to its nominal hull speed or beyond. Read more.
D/L = (D ÷ 2240) ÷ (0.01 x LWL)³
This ratio assess how quickly and abruptly a boat’s hull reacts to waves in a significant seaway, these being the elements of a boat’s motion most likely to cause seasickness. Read more.
Comfort ratio = D ÷ (.65 x (.7 LWL + .3 LOA) x Beam1.33)
This formula attempts to indicate whether a given boat might be too wide and light to readily right itself after being overturned in extreme conditions. Read more.
CSV = Beam ÷ ³√(D / 64)
The Pacific Seacraft 34 could be considered the encore act to a very successful Pacific Seacraft Crealock 37. Back in 1980, when Pacific Seacraft had freshly acquired the molds of the Crealock 37 from Cruising Consultants and continued its steady production, the company approached designer Bill Crealock to work on a smaller sibling. This new design became known as the Pacific Seacraft 34 (“Voyagemaker”) and it was introduced in 1984. Incidentally, this was the start of a long and very successful association between Pacific Seacraft and Bill Crealock.
It’s not surprising then that the boats share similar graceful lines and appearance. As with the 37, the 34 is focused on safety and comfort. Overall a tough boat with a seakindly nature very well suited for blue-water passage making for couples.
The Pacific Seacraft 34 has relatively large overhanging bow, a handsome sheer line, which ends with a traditional canoe stern. Under the waterline is a relatively long cruising fin keel with a very handy draft of 4’11 in standard trim that will get you into places that other boats wont (there’s also an option of a “very” shoal draft 4’1″ option). The rudder is skeg-hung.
The rig is of cutter configuration, all control lines are feed back into the safety of the cockpit. The cockpit is small, which some would say is a traditional blue-water design feature to advert the risk of pooping (flooding from a following sea), hence don’t be surprised if it gets cramped quickly as the people count climbs.
Inside, there is 6’4″ of headroom, a comfortably sized galley, and an interior that is well laid out for liveaboard. There are berths for up to five, two in the V, two in the saloon settees, and a single seagoing quarter berth which doubles as a seat for the nav table.
Sailing performance is spritely, when taking into account its relatively heavy displacement. The boat is well balanced and is capable of good upwind performance. As with all Pacific Seacraft boats, motion is seakindly, though there is some amount of hobby-horsing to windward due to the overhangs.
The hull is very solid GRP with the outer layer being in vinylester resin to resist osmotic blistering. The deck is cored with end grain balsa. The hull/deck join is above deck. The ballast is lead and externally bolted on. The interior pan runs the full length of the boat. Overall the workmanship is of a very high standard.
»Pacific Seacraft Official Site, Pacific Seacraft 34
This listing is presented by SailboatListings.com. Visit their website for more information or to contact the seller.
Great choice! Your favorites are temporarily saved for this session. Sign in to save them permanently, access them on any device, and receive relevant alerts.